Integrated environmental protection stove how to clean and maintain

One. Remove and clean step

1, with a cross-screwdriver to remove both sides of the cover plate support seat, and then with wood or cloth hammer upward tap two stove gap mouth, take away the cover plate, open two stove six self-tapping screws.

2. Lift the panel which is separated from the three sides slightly backward and upward so that the panel is completely separated from the gas collecting bin, and take it out for cleaning.

3. Hold the fire screen cover in the middle and back of the air anticlockwise direction by hand, turn the screen so that the three locks are separated, take out the fire screen cover and clean it.

4. Use one hand to hold the wheel and the other to hold the wheel lock nut. The clockwise direction is rotated and the wheel is removed for cleaning.

5. First, use the waste cloth to wipe away the oil stains in the air-collecting bin and the pot shell, then spray the inside of the air-collecting bin and the pot shell with alkaline cleaning agent or common cleaning agent. After more than ten minutes, wipe with the cloth, if it is not clean at one time, can Be repeated several times.

6. After cleaning, press down the order, step by step installation. Must be careful to ensure that the machine body in the cleaning and dismantling process is not damaged.

Second, the key parts of the clean maintenance

1. Pot holder

Use a soft brush to remove dirt from burner base surface, ignition needle and thermocouple protection needle surface. Avoid the use of particulate cleaning agents (detergent) , steel wire balls or knives to remove stubborn stains on the burner, which may damage the ignition needle and thermocouple flameout protection needle, therefore, the safety device of the integrated environmental protection cooker will break down or the surface of the components will be worn, which will directly affect the service life of the integrated cooker.

2. surface

Use soft gauze and soapy water (or special detergent) to clean and maintain the counter. Do not use granular cleaner or steel ball cleaning table, this will lead to scratches on the surface of stainless steel, affect the appearance of the cooker.

 3. Smoke inhalation channel

After long-term use of the integrated stove, a large amount of dirt will accumulate on the surface of the oil fume absorption passage, so it is necessary to clean the oil fume absorption passage at regular intervals. To clean the smoke absorption channel, use suitable oil remover to clean. Start the low-speed Range Hood, and then spray deoiling agent, so that the smoke inhalation channel, dirt will be inhaled deoiling agent after decomposition into the oil pan.

4, burner fire cover hole

In the use of the process, if the flame is found uneven or individual hole no flame, it is certainly the case of the plug of the fire cover. In such a case, it is necessary to timely clear the fire cover of the hole dredging. When cleaning, to wait for the burner cooling, and then take off the fire cover in time, with a steel needle to remove the hole of the dirt and carbon deposit.

5. Disinfect the inside of the cabinet

Wipe the water on the chassis and the dirt on the food shelf in time, and maintain the sterilizer regularly.

Integrated kitchen cleaning and maintenance precautions

1. After daily use, clean the kitchen cavity, face plate, cover plate and body surface with neutral detergent. Before cleaning the integrated stove, the gas valve must be cut off to ensure that the gas stove has been cooled. In the cleaning process, it is forbidden to disassemble the safety device and air-tightness parts of the gas stove to avoid destroying the integrated stove security system and the sealing system and affecting the use of the integrated stove.

2, when disassembly and cleaning, the motor and electrical parts can not be water, can not pull the internal connection wire, otherwise it will make the connection point loose, the part or parts to be taken down gently to avoid deformation.

 3. When cleaning the fire hole of the burner's fire cover, do not flush the fire cover directly with water (because the blister will temporarily plug the fire hole) , and do not wipe the burner surface with a hard object, this causes irreparable damage to the black surface enamel.

4, atmosphere gas stove cover and furnace core should regularly remove impurities and carbon on the hole, to prevent ignition failure or backfire and yellow flame. Liquefied Petroleum Gas, natural gas generally 90 days around a clean-up, artificial gas generally about 20 days a clean-up.

5, infrared stove ceramic plate should be kept clean, dry, not plug the hole. When cleaning, can use the waste toothbrush brush lightly brush the surface, must not use the hard object percussion and uses the water, uses the oil and so on other liquids to scrub.

6. electromagnetic cooker ceramic faceplate, after applying soft wet dishcloth to wipe, reoccupy sponge dips decontamination powder to wipe, use dishcloth to wipe finally clean, can not use sharp tool scraper.

7. The waste oil in the oil collection box is cleaned once every 1-3 months. When cleaning, press the oil collection box panel with your finger and push it to the bottom. Then slowly release your hand and the oil collection box slowly ejects, be careful of overfilling the tank.

8. Deep well side suction exhaust under the structure of integrated stove, oil point will naturally gather in the bottom of the body, oil adhesion speed is slow, generally in use about two years, need to clean the body.